Vertical Wind Turbine ElvWiS III ALUMINIUM Hybrid (240 W)

Two-stage full-metal wind turbine with Savonius rotor (assembly kit)Turbine components disassembled, generator fully assembled. Complete assembly material is included.With double-disc generator EGE600-VA and universal mount.Optional with 3-Phase rectifier or 12/24-Volt charge controller.Protection against theft by screwing the components.(Easily, you can choose the options beside the article images above in the variant configurator.)Scope of supplyGenerator (Aluminium, stainless steel bearings, stainless steel axle) Connection cable (0.3 m) Rotor-axis (galvanized steel) Rotor discs (Aluminium) Rotor blades (Aluminium) Universal mount (two-part, Aluminium, 1x stainless steel bearing) Assembly material (galvanized steel) 12/24-Volt charge controller (optional) 3-Phase rectifier (optional)Operating and instructions manual (digital)Technical data of the wind turbineTotal weight: 7.9 kg without cables and installation materialTotal height: 107 cmMaterial: seawater-resistant AluminiumSpinning start: 0.5 - 1.0 m/sCharging start 12.5 / 24.5 Volt: 3.0 - 4.0 / 5.0 - 6.0 m/sOperating range: 0.5 - 30 m/sOperating voltage: 0 - 59 Volts, optimised for 12-Volt applicationsOperational noise: < Ambient noise / 30 dB max.Dimensions of the rotor: B 40 x H 80 cmRotor nominal power at 12 m/s: 51 WattsRotor maximum power at 20 m/s: 237 WattsMaximum generator efficiency: 96 %Rotor type: Savonius rotor - 2 opposed C-shaped blades per levelRotor features: All-rounder for gusty and even wind conditions, quick start and direct reaction to changing wind speeds, reduced rotation speed at higher wind forces.Mounting options: For example, with U-clamps for mast mounting, firmly srewed and/or removable on (top)/under flat surfaces; horizontal or vertical mounting possible (on walls, roof top, boat deck/mast etc.).Component details Generator: 1 pieceConstruction: Double-disc generator (IP 54), 12-pole (24 neodymium magnets), AC 3-phase, brushless, cogging-free. Dimensions: Height 52 mm, corpus diameter 160 mm, diameter base plate 190 mm. Weight: ca. 3,5 kg Housing/Socket: Seawater-resistant Aluminium material with stainless-steel connecting elements. Axle: Stainless steel; equipped with precision ball bearing seatings and a axle stub with M12 external thread on top; for locking of the rotor axis equipped with a practical wrench attachment point. Bearings: Sturdy stainles steel ball bearings with lifetime lubrication.Cable connection: Strain relief below the generator bottom.Connection cable: 0.3 metersSpecifications: Flexible and durable equipment cable with 3 phases x 1.5 mm.Rotor axis: 1 pieceConstruction: Solid M12 threaded rod made of galvanized steel.Rotor disc: 3 piecesConstruction: Torsion-resistant, laser-cut disc made of seawater-resistant aluminum alloy. Rotor blade: 4 piecesConstruction: Stable, laser-cut and aerodynamically shaped blade with flanged long edges made of seawater-resistant aluminum alloy.Universal mount (two-part): 1 pieceConstruction: Robust, 4 mm thick aluminum bracket with reinforcing braces. Wind turbine can be installed or replaced without uninstalling the mount. Incl. ball bearing and bushing on top. Charge controller (optional): 1 piece Descripion: Waterproof encapsulated battery charge controller (12/24 V) with integrated rectifier (also suitable for LiFePo4 batteries). Charging mode: MPPT boost for low wind speeds Nominal voltage (battery): 12V / 24V auto detection Standby current consumption: 3.6 mA Boost charge start: 8-9 V (12 V Batt.) / 15-16 V (24 V Batt.) Protection class: IP 67 Power max.: 400 Watts Max. input voltage: 60 Volts Brake voltage: at 14.4 V (12 V batt.) / at 28.8 V (24 V batt.) Restart voltage: at 13.5 V (12 V batt.) / at 27.0 V (24 V batt.) Float voltage (after braking mode): down to 12.5 V (12 V batt.) / down to 25.0 V (24 V batt.) Detection voltage min.: 8 V Protection functions: Battery overvoltage, charging current limitation, braking function Working temperature: -35 °C - +75 °C / 85 % RH Display: Unload-LED, Charge-LED Cable connection: 3 x blue for generator alternating current, 1 x red for battery plus, 1 x black for battery minus. 3-Phase rectifier (optional): 1 piece Description: Waterproof encapsulated 3-phase bridge rectifier for direct connection of lighting, electric motors and other direct current applications. Function: Converts the alternating current of the generator into a direct current corresponding to the rotational speed. Connectors: 3 x AC plug connections for generator alternating current, 2 x DC plug connections for direct current consumers (plus +/minus -)

Two-stage full-metal wind turbine with Savonius rotor (assembly kit)Turbine components disassembled, generator fully assembled. Complete assembly material is included.With double-disc generator EGE400-VA and universal mount.Optional with 3-Phase rectifier or 12/24-Volt charge controller.Protection against theft by screwing the components.(Easily, you can choose the options beside the article images above in the variant configurator.)Scope of supplyGenerator (Aluminium, stainless steel bearings, stainless steel axle) Connection cable (0.3 m) Rotor-axis (galvanized steel) Rotor discs (Aluminium) Rotor blades (Aluminium) Universal mount (two-part, Aluminium, 1x stainless steel bearing) Assembly material (galvanized steel) 12/24-Volt charge controller (optional) 3-Phase rectifier (optional)Operating and instructions manual (digital)Technical data of the wind turbineTotal weight: 6.9 kg without cables and installation materialTotal height: 107 cmMaterial: seawater-resistant AluminiumSpinning start: 0.5 - 1.0 m/sCharging start 12.5 / 24.5 Volt: 3.0 - 4.0 / 5.0 - 6.0 m/sOperating range: 0.5 - 30 m/sOperating voltage: 0 - 59 Volts, optimised for 12-Volt applicationsOperational noise: < Ambient noise / 30 dB max.Dimensions of the rotor: B 32 x H 80 cmRotor nominal power at 12 m/s: 40 WattsRotor maximum power at 20 m/s: 187 WattsMaximum generator efficiency: 96 %Rotor type: Savonius rotor - 2 opposed C-shaped blades per levelRotor features: All-rounder for gusty and even wind conditions, quick start and direct reaction to changing wind speeds, reduced rotation speed at higher wind forces.Mounting options: For example, with U-clamps for mast mounting, firmly srewed and/or removable on (top)/under flat surfaces; horizontal or vertical mounting possible (on walls, roof top, boat deck/mast etc.).Component details Generator: 1 pieceConstruction: Double-disc generator (IP 54), 12-pole (24 neodymium magnets), AC 3-phase, brushless, cogging-free. Dimensions: Height 52 mm, corpus diameter 160 mm, diameter base plate 190 mm. Weight: ca. 3,5 kg Housing/Socket: Seawater-resistant Aluminium material with stainless-steel connecting elements. Axle: Stainless steel; equipped with precision ball bearing seatings and a axle stub with M12 external thread on top; for locking of the rotor axis equipped with a practical wrench attachment point. Bearings: Sturdy stainless steel ball bearings with lifetime lubrication.Cable connection: Strain relief below the generator bottom.Connection cable: 0.3 metersSpecifications: Flexible and durable equipment cable with 3 phases x 1.5 mm.Rotor axis: 1 pieceConstruction: Solid M12 threaded rod made of galvanized steel.Rotor disc: 3 piecesConstruction: Torsion-resistant, laser-cut disc made of seawater-resistant aluminum alloy. Rotor blade: 4 piecesConstruction: Stable, laser-cut and aerodynamically shaped blade with flanged long edges made of seawater-resistant aluminum alloy.Universal mount (two-part): 1 pieceConstruction: Robust, 4 mm thick aluminum bracket with reinforcing braces. Wind turbine can be installed or replaced without uninstalling the mount. Incl. ball bearing and bushing on top. Charge controller (optional): 1 piece Descripion: Waterproof encapsulated battery charge controller (12/24 V) with integrated rectifier (also suitable for LiFePo4 batteries). Charging mode: MPPT boost for low wind speeds Nominal voltage (battery): 12V / 24V auto detection Standby current consumption: 3.6 mA Boost charge start: 8-9 V (12 V Batt.) / 15-16 V (24 V Batt.) Protection class: IP 67 Power max.: 400 Watts Max. input voltage: 60 Volts Brake voltage: at 14.4 V (12 V batt.) / at 28.8 V (24 V batt.) Restart voltage: at 13.5 V (12 V batt.) / at 27.0 V (24 V batt.) Float voltage (after braking mode): down to 12.5 V (12 V batt.) / down to 25.0 V (24 V batt.) Detection voltage min.: 8 V Protection functions: Battery overvoltage, charging current limitation, braking function Working temperature: -35 °C - +75 °C / 85 % RH Display: Unload-LED, Charge-LED Cable connection: 3 x blue for generator alternating current, 1 x red for battery plus, 1 x black for battery minus. 3-Phase rectifier (optional): 1 piece Description: Waterproof encapsulated 3-phase bridge rectifier for direct connection of lighting, electric motors and other direct current applications. Function: Converts the alternating current of the generator into a direct current corresponding to the rotational speed. Connectors: 3 x AC plug connections for generator alternating current, 2 x DC plug connections for direct current consumers (plus +/minus -)

Two-stage quality wind turbine with Savonius rotor (assembly kit)Turbine components disassembled, generator fully assembled. Complete stainless steel assembly material is included.With double-disc generator GEA-400-VA and universal mount.Protection against theft by screwing the components.Optional with 3-Phase rectifier or 12/24-Volt charge controller.Optional upgrades for particularly demanding locations: Ceramic bearings and/or reinforcement angles on the mount.(Easily, you can choose the options beside the article images above in the variant configurator.)This turbine is a hybrid of the ALUMINUM and ADVENTURE series, which combines their proven advantages:- Large, solid rotor made of lightweight and durable aluminum.- Stable and torsion-resistant stainless steel hollow axle in the rotor.- Practical plug-in mounting of the rotor in the generator and upper bearing support.- Effective bolt connection between rotor and rotor axis.- Easy adjustment in the upper bearing by floating mounting.- Massive stainless steel ball bearings in generator and mount.Scope of supplyGenerator (ABS, stainless steel bearings, stainless steel axle) Connection cable (0.5 m)Turbine base plate: (Aluminium, segmented)Rotor retainer plate: (Aluminium) Rotor-axis (stainless steel) Rotor discs (Aluminium) Rotor blades (Aluminium) Universal mount (two-part, Aluminium) Assembly material (stainless steel) 12/24-Volt charge controller (optional)3-Phase rectifier (optional)Ceramic bearings instead of stainless steel bearings (optional)Reinforcement angles (4 pieces, optional)Operating and instructions manual (digital)Technical data of the wind turbineTotal weight: 6.5 kg without cables and installation materialTotal height: 107 cmMaterial: Stainless steel, seawater-resistant Aluminium, UV-resistant plasticsSpinning start: 0.5 - 1.0 m/sCharging start 12.5 / 24.5 Volt: 3.0 - 4.0 / 5.0 - 6.0 m/sOperating range: 0.5 - 30 m/sOperating voltage: 0 - 59 Volts, optimised for 12-Volt applicationsOperational noise: < Ambient noise / 30 dB max.Dimensions of the rotor: B 32 x H 80 cmRotor nominal power at 12 m/s: 40 WattsRotor maximum power at 20 m/s: 187 WattsMaximum generator efficiency: 96 %Rotor type: Savonius rotor - 2 opposed C-shaped blades per levelRotor features: All-rounder for gusty and even wind conditions, quick start and direct reaction to changing wind speeds, reduced rotation speed at higher wind forces.Mounting options: For example, with U-clamps for mast mounting, firmly srewed and/or removable on (top)/under flat surfaces; horizontal or vertical mounting possible (on walls, roof top, boat deck/mast etc.).Component detailsGenerator: 1 pieceConstruction: Double-disc generator (IP64), 12-pole (24 neodymium magnets), AC 3-phase, brushless, cogging-free. Housing/Socket: Extremely sturdy ABS compound material with stainless steel connecting elements. Axle: Stainless steel; equipped with precision ball bearing seatings and a zylindrical 18 mm axis retainer with integrated centering sleeve. Bottom with a M16 internal thread; on top equipped with a metric M22 wrench attachement point and a 5 mm trough hole for fixing a shaft.Bearings: Massive branded stainless steel ball bearings (Type 6005) with lifetime lubrication.Cable connection: Single implemented stable strain relief on generator. Turbine base plate segments: 2 piecesConstruction: Robust 4 mm aluminum solid sheet element. Compatible with the small universal mount. Multifunctional use provided by holes for attachment of additional securing and connecting elements.Rotor retainer plate: 1 piece Construction: Robust, 4 mm thick aluminum plate with precision-manufactured bearing sleeve made of impact- and abrasion-resistant polyamide. Solid branded stainless steel ball bearing (Type 6004) with lifetime lubrication and integrated 18 mm centering sleeve. Integrated slots for the compensation of alignment tolerances.Connection cable: 0.5 metersSpecifications: Flexible and durable 10 mm thick, rubberized outdoor equipment cable with 3 phases x 1.5 mm.Rotor axis: 1 pieceConstruction: All stainless steel-made, torsion resistant 18 mm hollow axle with cross hole to fix it into the generator, locking split-pins and protective cap. Rotor disc: 3 piecesConstruction: Torsion-resistant, laser-cut disc made of seawater-resistant aluminum alloy. Rotor blade: 4 piecesConstruction: Stable, laser-cut and aerodynamically shaped blade with flanged long edges made of seawater-resistant aluminum alloy.Universal mount (two-part): 1 pieceConstruction: Robust, 4 mm thick aluminum mount with 8 mm holes for mounting on planar surfaces or for mast mounting by the use of two 40 mm U-clamps. Wind turbine can be installed or replaced without uninstalling the mount. Charge controller (optional): 1 piece Descripion: Waterproof encapsulated battery charge controller (12/24 V) with integrated rectifier (also suitable for LiFePo4 batteries). Charging mode: MPPT boost for low wind speeds Nominal voltage (battery): 12V / 24V auto detection Standby current consumption: 3.6 mA Boost charge start: 8-9 V (12 V Batt.) / 15-16 V (24 V Batt.) Protection class: IP 67 Power max.: 400 Watts Max. input voltage: 60 Volts Brake voltage: at 14.4 V (12 V batt.) / at 28.8 V (24 V batt.) Restart voltage: at 13.5 V (12 V batt.) / at 27.0 V (24 V batt.) Float voltage (after braking mode): down to 12.5 V (12 V batt.) / down to 25.0 V (24 V batt.) Detection voltage min.: 8 V Protection functions: Battery overvoltage, charging current limitation, braking function Working temperature: -35 °C - +75 °C / 85 % RH Display: Unload-LED, Charge-LED Cable connection: 3 x blue for generator alternating current, 1 x red for battery plus, 1 x black for battery minus. 3-Phase rectifier (optional): 1 piece Description: Waterproof encapsulated 3-phase bridge rectifier for direct connection of lighting, electric motors and other direct current applications. Function: Converts the alternating current of the generator into a direct current corresponding to the rotational speed. Connectors: 3 x AC plug connections for generator alternating current, 2 x DC plug connections for direct current consumers (plus +/minus -)

Two-stage Savonius turbine 125S Stationary Set, Double Mount (assembly kit)Turbine components disassembled, generator fully assembled.Generator, rotor axis and rotor will be firmly screwed (maintenance-free, stainless-steel assembly material is included). Secured against theft by the firmly screwed components.Optional with 3-phase rectifier or 12/24-Volt charge controller. (Easily, you can choose the options beside the article images above in the variant configurator.) Scope of supply Generator (ABS, stainless steel bearings, stainless steel axle) Turbine base plate (segmented, Aluminium)Rotor retainer plate (Aluminium) Connection cable (0.5 m) Rotor-axis (Aluminium) Rotor discs (transparent, highly resistant polymer) Rotor blades (transparent, highly resistant polymer)Double universal mount (Aluminium)12/24-Volt charge controller (optional) 3-Phase rectifier (optional)Operating and instructions manual (digital) Technical data of the wind turbine Total weight: 5.0 kg incl. mountTotal height: 65 cm Material: Stainless steel, seawater-resistant Aluminium, UV-resistant plastics Spinning start: 0.5 - 1.0 m/s Charging start 12.5 / 24.5 Volt: 3.0 - 4.0 / 5.0 - 6.0 m/s Operating voltage: 0 - 59 Volts, optimised for 12-Volt applications Operational noise: < Ambient noise / 30 dB max. Operating range: 0.5 - 30 m/s Dimensions of the rotor: B 32 x H 45 cm Rotor nominal power at 12 m/s: 23 Watts Rotor maximum power at 20 m/s: 105 WattsMaximum generator efficiency: 96 %Rotor type: Savonius rotor - 2 opposed C-shaped blades per level Rotor features: All-rounder for gusty and even wind conditions, quick start and direct reaction to changing wind speeds, reduced rotation speed at higher wind forces.Mounting options: For example, mobile with U-clamps for mast mounting, firmly srewed and/or removable on (top)/under flat surfaces; horizontal or vertical mounting possible (on walls, caravan roof, roof top, boat deck/mast etc.). Component details Generator: 1 pieceConstruction: Double-disc generator (IP64), 12-pole (24 neodymium magnets), AC 3-phase, brushless, cogging-free. Housing/Socket: Extremely sturdy ABS compound material with stainless steel connecting elements. Axle: Stainless steel; equipped with precision ball bearing seatings and a zylindrical 18 mm axis retainer with integrated centering sleeve. Bottom with a M16 internal thread; on top equipped with a metric M22 wrench attachement point and a 5 mm trough hole for fixing a shaft.Bearings: Massive branded stainless steel ball bearings with lifetime lubrication.Cable connection: Single implemented stable strain relief on generator. Turbine base plate segments: 2 piecesConstruction: Robust 4 mm aluminum solid sheet element. Compatible with the small universal mount. Multifunctional use provided by holes for attachment of additional securing and connecting elements.Rotor retainer plate: 1 piece Construction: Robust, 4 mm thick aluminum plate with precision-manufactured bearing sleeve made of impact- and abrasion-resistant polyamide. Solid branded stainless steel ball bearing with lifetime lubrication and integrated 18 mm centering sleeve. Integrated slots for the compensation of alignment tolerances.Connection cable: 0.5 metersSpecifications: Flexible and durable 10 mm thick, rubberized outdoor equipment cable with 3 phases x 1.5 mm. Rotor axis: 1 pieceConstruction: All Aluminium steel-made, torsion resistant 18 mm hollow axle with cross hole to fix it into the generator, locking split-pins and protective cap. Rotor disc: 3 pieces (125S) / 5 pieces (325S)Construction: Rigid 2 mm thick sheet made of transparent, impact- and weather-resistant high-performance polymer. Precision machined centering sleeves made of impact- and abrasion-resistant polyamide with integrated axle locking. Special features: Individually paintable with Lexan colors. Rotor blade: 4 pieces (125S) / 8 pieces (325S)Construction: Flexible, aerodynamically shaped blade made of transparent, impact- and weather-resistant high-performance polymer. Special features: Individually paintable with Lexan colors. Universal mount (two-part): 1 pieceConstruction: Robust, 4 mm thick aluminum mount with 8 mm holes for mounting on planar surfaces or for mast mounting by the use of two 40 mm U-clamps. Wind turbine can be installed or replaced without uninstalling the mount. Charge controller (optional): 1 piece Descripion: Waterproof encapsulated battery charge controller (12/24 V) with integrated rectifier (also suitable for LiFePo4 batteries). Charging mode: MPPT boost for low wind speeds Nominal voltage (battery): 12V / 24V auto detection Standby current consumption: 3.6 mA Boost charge start: 8-9 V (12 V Batt.) / 15-16 V (24 V Batt.) Protection class: IP 67 Power max.: 400 Watts Max. input voltage: 60 Volts Brake voltage: at 14.4 V (12 V batt.) / at 28.8 V (24 V batt.) Restart voltage: at 13.5 V (12 V batt.) / at 27.0 V (24 V batt.) Float voltage (after braking mode): down to 12.5 V (12 V batt.) / down to 25.0 V (24 V batt.) Detection voltage min.: 8 V Protection functions: Battery overvoltage, charging current limitation, braking function Working temperature: -35 °C - +75 °C / 85 % RH Display: Unload-LED, Charge-LED Cable connection: 3 x blue for generator alternating current, 1 x red for battery plus, 1 x black for battery minus. Accessories: Fuse holder and fuse 3-Phase rectifier (optional): 1 piece Description: Waterproof encapsulated 3-phase bridge rectifier for direct connection of lighting, electric motors and other direct current applications. Function: Converts the alternating current of the generator into a direct current corresponding to the rotational speed. Connectors: 3 x AC plug connections for generator alternating current, 2 x DC plug connections for direct current consumers (plus +/minus -) Accessories: Fuse holder and fuse